Free NACE-CIP1-001 Sample Questions and 100% Cover Real Exam Questions (Updated 100 Questions)
Download Real NACE NACE-CIP1-001 Exam Dumps Test Engine Exam Questions
NEW QUESTION # 38
If inspectors identify issues of non-conformance during an inspection, they should
- A. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- B. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- C. perform additional tests secretly to ensure there are no other potential issues at the site
- D. wait until the final report is being prepared to identify the issues in writing so they are fully documented
Answer: B
NEW QUESTION # 39
Most industrial coatings are:
- A. Organic
- B. Inorganic
- C. Resistant to temperatures above 200C
- D. Resistant to concentrated sulfuric acid
Answer: A
NEW QUESTION # 40
The least effective method of surface cleaning is most likely
- A. power tool cleaning.
- B. dry grit blasting.
- C. hand tool cleaning.
- D. water blasting.
Answer: C
NEW QUESTION # 41
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
- B. Hire a third patty to assist you in understanding the document
- C. Carefully review the document and do the best you can
- D. Advise the owners' representative of your lack of knowledge in this area
Answer: C
NEW QUESTION # 42
Dew point is the temperature at which
- A. water freezes.
- B. the air is saturated.
- C. humidity decreases
- D. condensation occurs.
Answer: D
NEW QUESTION # 43
Corrosion generally occurs at which of the following sites:
- A. Anode
- B. Metallic pathway
- C. Electrolyte
- D. Cathode
Answer: A
NEW QUESTION # 44
In a non-convertible coating the role of the primary solvent is to:
- A. To control the evaporation rate
- B. To dissolve the resin
- C. To promote faster cure
- D. To make the coating flow out better
Answer: A
NEW QUESTION # 45
Daily reports are important because:
Select All That Apply
- A. the information impacts future projects.
- B. Management uses them to make personnel decisions.
- C. Inspectors rarely change on a project.
- D. The information aids communication with supervisors.
Answer: A,B,D
NEW QUESTION # 46
According to SSPC PA 2 a Spot Measurement is:
- A. The overall average of all readings
- B. The average of all spot measurements in a given area
- C. A single gauge reading
- D. The average of gauge readings taken in a 4cm (1.5 inch) circle
Answer: D
NEW QUESTION # 47
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Ultra-Violet light may contaminant the surface
- B. Synthetic oil or grease may not be identified
- C. Presence of weld spatter may produce a false positive
- D. Chloride salt may produce a false positive
Answer: B
NEW QUESTION # 48
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks and consult the Owner's representative for direction
- B. Keep doing the checks regardless
- C. Skip the checks and just record the same readings as you have been getting
- D. Skip the checks as you are. confident the blast pressure is OK
Answer: A
NEW QUESTION # 49
Checking is
- A. a fine crack in the surface of a coating that rarely reaches the substrate
- B. an exposed area of the substrate or previous coat material, caused by poor application technique.
- C. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
- D. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
Answer: A
NEW QUESTION # 50
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Use another method as the comparator method is too subjective
- B. Record the segment with the more aggressive profile
- C. Record your result by identifying two segments
- D. Record the segment with the less aggressive profile
Answer: D
NEW QUESTION # 51
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Check the credentials of the Safety Officer on site
- B. Check the PPE used by the Applicators
- C. Act in accordance with the site safety requirements and set an example
- D. Assume the role of the Safety Inspector
Answer: C
NEW QUESTION # 52
SSPC SP 1 identifies the use of:
- A. Inorganic solvents
- B. Biodegradable detergents
- C. A wide variety of materials
- D. Organic solvents
Answer: C
NEW QUESTION # 53
......
New NACE-CIP1-001 exam dumps Use Updated NACE Exam: https://www.exam4docs.com/NACE-CIP1-001-study-questions.html
Verified NACE-CIP1-001 Dumps Q&As - NACE-CIP1-001 Test Engine with Correct Answers: https://drive.google.com/open?id=11BEFHdNs1gDlAqmuUr3h3iln_9RIxOKK
